954 viewsBumper cover removed as I begin the trimming of the front Jul 16, 2026 at 08:59 AM
|
|
955 viewsDriver side inner fender remounted Jul 16, 2026 at 08:57 AM
|
|
957 viewsAFTER !! Jul 16, 2026 at 08:53 AM
|
|
1014 viewsRear differential drain plug (if you can call that rubber pos that) leaking so I replaced it with new one and topped off rear end grease as axle grease seals were leaking into the breaks. I will be rebuilding the rear end soon as it has been roaring since I bought it. Jul 16, 2026 at 08:53 AM
|
|
966 viewsLooking at the 120 foot oak tree the neighbor paid us to take down so it wouldn't hit his house. I am glad we did not drop it on the house !! Jul 16, 2026 at 08:52 AM
|
|
1014 viewsTyler working to top the treeJul 16, 2026 at 08:52 AM
|
|
958 viewsremoved one piece of tape and cut slits all the way down the piece so it could be folded over to make a nice edge. Not only to eliminate the sharp thin edge but, to make it stronger and to have something to mount the trim piece back to once I cut it down to size. Jul 16, 2026 at 08:52 AM
|
|
965 viewsTyler helping me to dig out an old gutter drain to replace with new plastic pipe. Jul 16, 2026 at 08:50 AM
|
|
1016 viewsTrimmed the back edge as well just like the other side. Jul 16, 2026 at 08:49 AM
|
|
1025 viewsdriveshaft mounted to transfer caseJul 16, 2026 at 08:48 AM
|
|
929 viewsPretty close on rear but should not be a problem, if it is I`ll trim it. Jul 16, 2026 at 08:43 AM
|
|
951 viewsremoving old lower isolator Jul 16, 2026 at 08:43 AM
|
|
969 viewsThese are the rims/tires I am wishing to put on after the liftJul 16, 2026 at 08:42 AM
|
|
984 viewsPinch weld ground back significantly. Most people beat that over flat or cut it out and weld a flat piece back. Not needed in my case. any larger tire and I would have to. Jul 16, 2026 at 08:35 AM
|
|
952 viewsAnother view of the slits I cut in it. Jul 16, 2026 at 08:29 AM
|
|
991 viewsdriveshaft mounted to front diffJul 16, 2026 at 08:29 AM
|
|
928 viewsCutting the first section out. Jul 16, 2026 at 08:28 AM
|
|
951 viewsHad to drill the slot out so the plastic mounting tab on the trim would fit back in Jul 16, 2026 at 08:27 AM
|
|
1013 viewsCustom fitting the end cap Jul 16, 2026 at 08:26 AM
|
|
943 viewsTyler splitting wood at another neighbors house after dropping a 120 foot tall Oak. Jul 16, 2026 at 08:23 AM
|
|
990 viewsI did another small cut and bent the metal around to protect the washer fluid reservoir. Jul 16, 2026 at 08:22 AM
|
|
963 viewsFront diff = old oil seal after yoke removed Jul 16, 2026 at 08:17 AM
|
|
1014 viewstop isolator on rear coil ,, badly squished and worn Jul 16, 2026 at 08:14 AM
|
|
922 viewsTyler sawing a path through a blow down on my section of the Appalachian Trail. Jul 16, 2026 at 08:14 AM
|
|
| 268 files on 12 page(s) |
 |
|
|
|
|
|
|
|
|
11 |
|
