RATtreks.com - Images of RATventures

Home > Misc.

Last viewed - Misc.
5821.jpg
1661 viewsNeighbors fallen oak tree after we cut it up and drug it over to our property. Nov 14, 2026 at 09:47 PM
4453.jpg
1045 viewsTyler taking down trees around the property Nov 14, 2026 at 09:45 PM
0590.jpg
984 viewsThese are the rims/tires I am wishing to put on after the liftNov 14, 2026 at 09:44 PM
5825.jpg
1399 viewsSubmitted by Bol'DarNov 14, 2026 at 09:43 PM
shrimp_plant.jpg
1390 viewsdad's flowersNov 14, 2026 at 09:43 PM
0889.jpg
919 viewsFolded over to make the new edge Nov 14, 2026 at 09:42 PM
0625.jpg
1017 viewsHad to clean all this up and sand it good and painted with rust inhibitor (POR) Nov 14, 2026 at 09:41 PM
3705.jpg
982 viewsTyler cutting up the 120 ft Oak at other neighbors house. Nov 14, 2026 at 09:41 PM
0861.jpg
1033 viewsTrimmed the back edge as well just like the other side. Nov 14, 2026 at 09:41 PM
5798.jpg
1401 viewsSubmitted by Bol'DarNov 14, 2026 at 09:41 PM
5483.jpg
1096 viewsTyler weed eating on my section of the Appalachian Trail. Nov 14, 2026 at 09:40 PM
wildflowers4.jpg
1465 viewsWildflowers along AT on Elk RiverNov 14, 2026 at 09:35 PM
0586.jpg
1023 viewsFactory height (actually a little under due to deteriorated coil spring isolators which are also being replaced) Nov 14, 2026 at 09:30 PM
wisteria.jpg
1276 viewsdad's WisteriaNov 14, 2026 at 09:30 PM
lily.jpg
1399 viewsdad's flowersNov 14, 2026 at 09:26 PM
5826.jpg
1411 viewsSubmitted by Bol'DarNov 14, 2026 at 09:26 PM
0806.jpg
916 viewsA bit close on back of front fender ! Nov 14, 2026 at 09:26 PM
0858.jpg
1011 viewsWorking out a way to mount the inner fender to the newly trimmed bumper cover so I wouldnt have to cut it as well. It worked out perfect. Nov 14, 2026 at 09:26 PM
2917.jpg
971 viewsTyler doing some rappellingNov 14, 2026 at 09:26 PM
id_gmc_afkx_01.jpg
1203 viewsNov 14, 2026 at 09:25 PM
0901.jpg
1066 viewsPrimed it well. Nov 14, 2026 at 09:24 PM
0647.jpg
1002 viewsNew isolators and spacer installed Nov 14, 2026 at 09:22 PM
0841.jpg
934 viewsPass side. That piece of metal is usually completely removed on these type of jobs but, I decided not to. I cut it and bent it over where the two horns are. I had to modify the horns position so that the wires came down from top instead of sticking out the back which worked well. Nov 14, 2026 at 09:19 PM
1036.jpg
921 viewsAFTER painting the trim black ! And a new black grille,, Nov 14, 2026 at 09:14 PM
268 files on 12 page(s) 1