1029 viewsI kept trimming until I got the look I was after Aug 21, 2026 at 02:50 AM
|
|
929 viewsEpoxy applied to the driver side corner piece I made and riveted on Aug 21, 2026 at 02:50 AM
|
|
957 viewsremoving old isolator Aug 21, 2026 at 02:48 AM
|
|
924 viewsepoxy glue on pass side Aug 21, 2026 at 02:47 AM
|
|
1069 viewsAFTER ! Aug 21, 2026 at 02:45 AM
|
|
962 viewsremoved one piece of tape and cut slits all the way down the piece so it could be folded over to make a nice edge. Not only to eliminate the sharp thin edge but, to make it stronger and to have something to mount the trim piece back to once I cut it down to size. Aug 21, 2026 at 02:44 AM
|
|
975 viewsThese are the rims/tires I am wishing to put on after the liftAug 21, 2026 at 02:44 AM
|
|
943 viewsTaping it up to paint the trim black Aug 21, 2026 at 02:42 AM
|
|
900 viewsHere is how much room I was able to get on the first side by jacking the other side up so far, Aug 21, 2026 at 02:42 AM
|
|
903 viewsA bit close on back of front fender ! Aug 21, 2026 at 02:42 AM
|
|
965 viewsAFTER ! Aug 21, 2026 at 02:42 AM
|
|
919 viewsAFTER painting the trim black ! And a new black grille,, Aug 21, 2026 at 01:49 AM
|
|
1039 viewsMeasured it to be the same as pass side and taped it Aug 21, 2026 at 01:39 AM
|
|
915 viewsMetal cut and bent, horn wires relocated I am going to save the inner fenders too. (something else most people do away with when doing this) Aug 21, 2026 at 01:34 AM
|
|
1012 viewsFront bumper lower part trimmed Aug 21, 2026 at 01:04 AM
|
|
855 viewscleaned and ready for POR Aug 21, 2026 at 01:04 AM
|
|
1011 viewsnew oil seal installed on transfer caseAug 20, 2026 at 07:42 PM
|
|
955 viewsNew gutter drain after removing the old clay pipes. Aug 20, 2026 at 07:42 PM
|
|
938 viewsboth driveshafts. The double cardan one came from Iron Rock OffroadAug 20, 2026 at 07:42 PM
|
|
952 viewsTyler digging out the old clay gutter drain pipe. Aug 20, 2026 at 07:42 PM
|
|
929 viewsRubber isolators badly worn back there too Aug 20, 2026 at 06:15 PM
|
|
1066 viewsNew front driveshaft done Aug 20, 2026 at 05:58 PM
|
|
1030 viewsdriveshaft mounted to transfer caseAug 20, 2026 at 05:54 PM
|
|
1001 viewsAFTER trimming the fender (I will trim that top part later after I see if I go with a bushwhacker flare OR if I do something custom) For now I have all the clearance i need and it doesnt look that bad but that will get trimmed eventually !!! Aug 20, 2026 at 05:53 PM
|
|
| 268 files on 12 page(s) |
 |
|
|
|
|
|
|
|
10 | |
|
