1039 viewsJacking up one side as far as it will go to give room to get the coil back in with new rubbers and the spacer. Nov 14, 2026 at 07:29 PM
|
|
977 viewsBumper cover removed as I begin the trimming of the front Nov 14, 2026 at 07:28 PM
|
|
1008 viewsI did another small cut and bent the metal around to protect the washer fluid reservoir. Nov 14, 2026 at 07:28 PM
|
|
947 viewsTrimmed the trim piece to fit cutting the door side off so as to keep the part that went around the fender so it would look like it was meant to be there and would still have the mounting screw holes to attach it with. Nov 14, 2026 at 07:27 PM
|
|
999 viewsFirst I cut out a large slot in the lower end of the bumper cover Nov 14, 2026 at 07:26 PM
|
|
906 viewsTyler working to top the tree. Nov 14, 2026 at 07:26 PM
|
|
1275 viewsNew isolators and spacer installed Nov 14, 2026 at 07:26 PM
|
|
983 viewsNew isolators and spacer installed Nov 14, 2026 at 07:26 PM
|
|
1043 viewsI expected it to rub the lower short arm but it does not. Many use wheel spacers due to that but I will not have to. Nov 14, 2026 at 07:25 PM
|
|
986 viewsNow to trim the back of the front fenders. First thing, remove the trim. Nov 14, 2026 at 07:23 PM
|
|
941 viewsA bit close on front bumper ! Nov 14, 2026 at 07:23 PM
|
|
1351 viewsWhile pass side primer was drying I moved to the driver side. This one went much quicker like under an hour now that I had the process down pat. Nov 14, 2026 at 07:22 PM
|
|
1018 viewsnew oil seal installed on front diffNov 14, 2026 at 07:18 PM
|
|
912 viewsHere is how much room I was able to get on the first side by jacking the other side up so far, Nov 14, 2026 at 07:18 PM
|
|
952 viewsCoil spring retainer installed on driver side (remember that tower was rusted nearly gone ??) Just one less thing to worry about when going down the trail !! Nov 14, 2026 at 07:17 PM
|
|
972 viewsFront after trimming Nov 14, 2026 at 07:17 PM
|
|
925 viewshere is height AFTER the lift and rims/tires. Between the 2.5 lift, new isolators and shocks, I managed to get a total of 6 inches of lift. (was 31 inches) Nov 14, 2026 at 07:17 PM
|
|
1082 viewsAFTER ! Nov 14, 2026 at 07:17 PM
|
|
930 viewsTyler makes the final cut. Nov 14, 2026 at 07:15 PM
|
|
923 viewsTyler working on the neighbors tree. Nov 14, 2026 at 07:15 PM
|
|
980 viewsTyler roping down a tree,, Nov 14, 2026 at 07:12 PM
|
|
1015 viewsView of the inner fender folded around and bolted to the lower part of the metal inner bumperNov 14, 2026 at 07:10 PM
|
|
984 viewsThe amount of tools needed for this job. Nov 14, 2026 at 07:07 PM
|
|
1518 viewsdad's yellow roseNov 14, 2026 at 07:03 PM
|
|
| 268 files on 12 page(s) |
 |
|
4 | |
|
|
|
|
|
|
|
