2557 viewsHUGE Oak tree that fell and almost crushed our neighbors house. Tyler and I removed it for them. Nov 14, 2026 at 07:36 PM
|
|
926 viewsNo problem getting the first one in Nov 14, 2026 at 07:34 PM
|
|
1475 viewsSubmitted by Bol'DarNov 14, 2026 at 07:34 PM
|
|
1026 viewsFront part of pass side inner fender looking good after mounting to bumper coverNov 14, 2026 at 07:34 PM
|
|
983 viewsSide view. I would be grinding back the pinch weld quite a bit too. Nov 14, 2026 at 07:34 PM
|
|
1016 viewsI reused the cut pieces and riveted them back to the trimmed bumper corners so I would have a nice edge instead of a narrow cut one and a way to mount the inner fenders back to it. I would epoxy glue those later in this process for stability as those rivets would never last by themselves under off roading conditions. Nov 14, 2026 at 07:34 PM
|
|
1009 viewsnew rims /tires mounted . These are JK take offs and are 255/75.17 so the tires are 32.5 inches tall. Nov 14, 2026 at 07:32 PM
|
|
979 viewsNow I replaced the plastic bumper cover so I cut start cutting it. Nov 14, 2026 at 07:32 PM
|
|
950 viewsI dropped this 120 footer (Oak) at neighbors house. If not taken down it could have hit the house. (it got a blue fungus and died suddenly) Nov 14, 2026 at 07:32 PM
|
|
852 viewshere you can see just how high I jacked it up to eliminate so much prying and straining ! Nov 14, 2026 at 07:31 PM
|
|
1583 viewsdad's flowersNov 14, 2026 at 07:29 PM
|
|
1039 viewsJacking up one side as far as it will go to give room to get the coil back in with new rubbers and the spacer. Nov 14, 2026 at 07:29 PM
|
|
1008 viewsI did another small cut and bent the metal around to protect the washer fluid reservoir. Nov 14, 2026 at 07:28 PM
|
|
947 viewsTrimmed the trim piece to fit cutting the door side off so as to keep the part that went around the fender so it would look like it was meant to be there and would still have the mounting screw holes to attach it with. Nov 14, 2026 at 07:27 PM
|
|
999 viewsFirst I cut out a large slot in the lower end of the bumper cover Nov 14, 2026 at 07:26 PM
|
|
906 viewsTyler working to top the tree. Nov 14, 2026 at 07:26 PM
|
|
1275 viewsNew isolators and spacer installed Nov 14, 2026 at 07:26 PM
|
|
983 viewsNew isolators and spacer installed Nov 14, 2026 at 07:26 PM
|
|
1043 viewsI expected it to rub the lower short arm but it does not. Many use wheel spacers due to that but I will not have to. Nov 14, 2026 at 07:25 PM
|
|
986 viewsNow to trim the back of the front fenders. First thing, remove the trim. Nov 14, 2026 at 07:23 PM
|
|
941 viewsA bit close on front bumper ! Nov 14, 2026 at 07:23 PM
|
|
1018 viewsnew oil seal installed on front diffNov 14, 2026 at 07:18 PM
|
|
912 viewsHere is how much room I was able to get on the first side by jacking the other side up so far, Nov 14, 2026 at 07:18 PM
|
|
952 viewsCoil spring retainer installed on driver side (remember that tower was rusted nearly gone ??) Just one less thing to worry about when going down the trail !! Nov 14, 2026 at 07:17 PM
|
|
| 268 files on 12 page(s) |
 |
|
|
|
6 | |
|
|
|
|
|
